Print this list

Customer Reference Specifications-List of Changes: 2012, 2011, 2010
Complete List of Changes for Sketches: 2011, 2010
REMSI Rules - List of Changes: 2011, 2010
Definitions - List of Changes: 2011
Approved Metering and Equipment Tables-List of Changes: 2012, 2011, 2010

NOTE

"PPL" and "Company" will be changed to "PPL EU", "PPL's" and "Company's" will be changed to "PPL EU's".

NOTE 1

All updated sketches have been redrawn for clarity using a new format.

NOTE 2

The 3 phase, 4 wire, 240-single phase 120/240 volts service is now referred to as 3 Phase, 4 Wire, Delta 240/120 Volts.

NOTE 3

Are changing the terms ' meter trough' to 'meter base' and 'meter mounting' to 'meter panel'.

03/18/11 Updated Format and Content

Sketch 16 Series - Sketch 16A has been revised, reformatted and updated into a series of sketches:

• Sketch 16 - up to and including 2000A - 8 conduits
• Sketch 16A - up to and including 3000A - 12 conduits
• Sketch 16B - up to and including 4000A - 16 conduits

04/07/10 New Sketch

09/17/10 renumbered to mimic organization of previous 41 Series Sketches. Notes have been expanded, the drawing updated accordingly and the detail box added.

Old Numbering:
Sketch 41P1 – Manual Transfer Switch – Partial Load – Less than 600V
Sketch 41P2 – Manual Transfer Switch – Full Load – Less than 600V
Sketch 41AP1 – Automatic Transfer Switch – Partial Load – Less than 600V
Sketch 41AP2 – Automatic Transfer Switch – Full Load – Less than 600V
Sketch 41BP1 – Manual or Automatic Transfer Switch - Partial Load – 12KV Load Center
Sketch 41BP2 – Automatic Transfer Switch – Full Load – 12KV Load Center
Sketch 41BP3 – Manual or Automatic Transfer Switch – 12KV Switchgear
Sketch 41CP1 – Manual or Automatic Transfer Switch – 12KV Switchgear

New Numbering:
Sketch 41P1 – Manual Transfer Switch – Partial Load – Less than 600V
Sketch 41P2 – Manual Transfer Switch – Full Load – Less than 600V
Sketch 41AP1 – Automatic Transfer Switch – Partial Load – Less than 600V
Sketch 41AP2 – Automatic Transfer Switch – Full Load – Less than 600V
Sketch 41BP1 – Manual Transfer Switch – Partial Load – 12KV Load Center
Sketch 41BP2 – Manual Transfer Switch – Full Load – 12KV Load Center
Sketch 41CP1 – Automatic Transfer Switch – Partial Load – 12KV Load Center
Sketch 41CP2 – Automatic Transfer Switch – Full Load – 12KV Load Center
Sketch 41DP1 – Manual Transfer Switch – 12KV Switchgear
Sketch 41EP1 – Automatic Transfer Switch – 12KV Switchgear

6-10-165 Outdoor Lighting - Requirements for Service to Customer-Owned Street Lighting Systems Served Under Rate Schedule SE

• 10/31/11 Sheet 1-16
• Updated wordings of general notes and updated numbers in Sheets 2 and 3.
• Updated last paragraph in Sheet 4.
• Updated sheet numbers in Sheet 5.
• Updated figure and sheet number in Sheet 6.
• Updated last paragraph and figures number on Sheet 7.
• Updated sheet numbers in Sheet 8.
• Updated figure and sheet number in Sheet 9.
• Updated diagram label in Sheet 10.
• Updated diagram label in Sheet 11.
• Updated diagram clearance in Sheet 12.
• Updated figure number and updated diagram in Sheet 13.
• Updated diagram label and dimensions. Updated format in Sheet 15.
• Updated figures, number and fonts.

6-09-194 Overhead Service to Overhead

• 09/08/11 Sheet 1
  • Made into formal title page, content now starts on Sheet 2.
  • Added statement, specifying CRS 6-09-194 is part of the Rules for Electric Meter and Service Installation (REMSI) Website.
• 09/08/11 Sheet 2
  • Split Note 1 into Note 1 and 2.
  • Re-numbered notes accordingly.
  • Updated new Note 4 - ground wire comes from the lightning arrestor cross arm.
• 09/08/11 Sheet 3
  • Updated Bill of Material to meet current requirements.
• 09/08/11 Sheet 4
  • Updated Bill of Material to meet current requirements.
• 09/08/11 Sheet 5
  • Updated drawing notes to match Bill of Material changes.
• 09/08/11 Sheet 6
  • Updated drawing notes to match Bill of Material changes.
• 09/08/11 Sheet 7
  • Metering Compartment Drawing - added references to Note 18 and Note 19.
  • Removed Detail B. Terminal block is to be attached to neutral bar; previously terminal block was attached to the side of the termination compartment.
  • Updated minimum working clear space in front of metering compartment to 9' 0" from 5' 0".

6-09-199 Installation Instructions For 3-Phase, 4 Wire WYE 7,200/12,470V Service Termination and Metering Compartments in Customer-Owned Switchgear

• 09/08/11 Sheet 5
  • Bill of Material item 3 updated.
• 09/08/11 Sheet 7
  • Updated drawing - VT's to be mounted on shelf instead of on back of metering compartment.

6-14-121 Requirements for Trenching and Backfilling by Developer/Customer for Primary and Secondary Installation in a Trench with Only Electric Lines (Non-Joint Trench)

• 09/08/11 Sheet 1
  • Updated title.
  • Made into formal title page, content now starts on Sheet 2.
  • Added statement, specifying CRS 6-14-121 is part of the Rules for Electric Meter and Service Installation (REMSI) Website.
• 09/08/11 Sheet 2
  • Added reference to CRS 6-15-180.
  • Updated information in Note 2.
• 09/08/11 Sheet 4
  • Added flow-able fill as a select backfill option
• 09/08/11 Sheet 5
  • Notes expanded to Sheet 5, all pages from this point forward were renumbered accordingly.
• 09/08/11 Sheet 6
  • Updated drawing notes and added more detail on dimensions.
• 09/08/11 Sheet 7
  • Updated drawing for content and clarity.

6-14-122 Requirements for Trenching and Backfilling by Developer/Customer for Primary and Secondary Installation in a Trench with Electric and/or Gas, Telecommunication Lines (Joint Trench)

• 09/08/11 Sheet 1
  • Updated title.
  • Made into formal title page, content now starts on Sheet 2.
  • Added statement, specifying CRS 6-14-122 is part of the Rules for Electric Meter and Service Installation (REMSI) Website.
• 09/08/11 Sheet 2
  • Added reference to CRS 6-15-180.
  • Updated information in Note 2.
• 09/08/11 Sheet 4
  • Added flow-able fill s a select backfill option.
• 09/08/11 Sheet 5
  • Notes expanded to Sheet 5, all pages from this point forward were renumbered accordingly.
• 09/08/11 Sheet 6
  • Updated drawing notes and added more detail on dimensions.
• 09/08/11 Sheet 7
  • Updated drawing for content and clarity.
• 09/08/11 Sheet 8
  • Updated drawing for content and clarity.
• 09/08/11 Sheet 9
  • Updated drawing for content and clarity.

6-19-100 Customer Low-Voltage Switchboards Service Cable Terminal Compartment Arrangements and Clearances

• 03/19/10 Sheet 1
  • Made into formal title page, content now starts on Sheet 2.
  • Added statement, specifying CRS 6-19-100 is part of the Rules for Electric Meter and Service Installation (REMSI) Website.
• 03/19/10 Sheet 2
  • Added Note 1 - Preapproved List and renumber notes going forward.
• 03/19/10 Sheet 3
  • In Note 6 (previous Note 5) revised to state connectors are of set-screw type, not compression or set-screw as previously stated.
• 03/19/10 Sheet 4
  • In Note 8 (previous Note 7) stated when cable limiters are installed set-screw type bus connectors are not required.
  • Corrected table numbering to Table 1 (previously stated Table 4).
  • Table 2 moved to Sheet 5.
• 03/19/10 Sheet 5
  • Table 4 moved to Sheet 6.
• 03/19/10 Sheet 6
  • Figure 1 moved to Sheet 7.
• 03/19/10 Sheet 7
  • Figure 2 moved to Sheet 8.
• 03/19/10 Sheet 8
  • Figure 3 moved to Sheet 9.
• 03/19/10 Sheet 9
  • Figure 4 moved to Sheet 10.
• 03/19/10 Sheet 10
  • Figure 5 moved to Sheet 11.
  • Added note referring grounding bushings to Note 7 (previously Note 6).
• 03/19/10 Sheet 11
  • Figure 7 moved to Sheet 12 and renumbered to Figure 6.
  • Added note referring grounding bushings to Note 7 (previously Note 6).
• 03/19/10 Sheet 12
  • Previous Sheet 12 deleted - obsolete.
  • Revised dimensions to state 50" (previously 36") required to the side and rear of terminal compartment if access is required.

6-15-180 Customer Installed Duct System

• 03/19/10 Sheet 1
  • Made into formal title page, content now starts on sheet 2.
  • Added statement, specifying CRS 6-15-180 is part of the Rules for Electric Meter and Service Installation (REMSI) Website.
• 03/19/10 Sheet 2
  • Updated wording for consistency, final grade to finished grade.
• 03/19/10 Sheet 4
  • Added language about sweeps to Note 7.
  • Note 9 was note 11 on previous version.
  • All other notes were renumbered accordingly.
• 03/19/10 Sheet 5
  • Added statement to Note 10 that PPL EU will inspect conduit installation prior to being pulled.
  • Added more detail to Note 10 about tamping concrete to ensure conduits are fully encased.
  • Changed title of Note 12 to Pulling Line.
  • Corrected breaking strength of pulling line from 200 to at least 1200 lbs.
  • Added more detail to Note 12 about pulling line requirements.
• 03/19/10 Sheet 6
  • Updated Note References.

6-10-165 Requirements for Service to Customer-Owned Street Lighting Systems Served Under Rate Schedule SE

• 03/19/10 Sheet 1
  • Made into formal title page, content now starts on sheet 2.
  • Added statement, specifying CRS 6-10-165 is part of the Rules for Electric Meter and Service Installation (REMSI) Website.
• 03/19/10 Sheet 2
  • Revised Note 7.
• 03/19/10 Sheet 3
  • Revised Note 14.
• 03/19/10 Sheet 4
  • Revised Support and Support Brackets #1 sectiion to reference REMSI Sketch #47.
  • Revised Identification Section to include pole label information.
• 03/19/10 Sheet 5
  • Removed last line of Customer Shall Provide The Following For New Installation #2.
• 03/19/10 Sheet 7
  • Added more detail to first paragraph.
• 03/19/10 Sheet 8
  • Added two notes referenced on sheet marked as * and **.
• 03/19/10 Sheet 9
  • Added one note referenced on sheet marked as *.
  • Updated Dimensions.
  • Noted Drawing is Not to Scale.
• 03/19/10 Sheet 10
  • Added one note referenced on sheet marked as *.
  • Updated Dimensions.
  • Noted Drawing is Not to Scale.
• 03/19/10 Sheet 11
  • Noted Drawing is Not to Scale.
• 03/19/10 Sheet 12
  • Noted Drawing is Not to Scale.
• 03/19/10 Sheet 13
  • Added one note referenced on sheet marked as *.
  • Updated Dimensions.
  • Noted Drawing is Not to Scale.
    

6-09-199 Installation Instructions For 3-Phase, 4 Wire WYE 7,200/12,470V Service Termination and Metering Compartments In Customer-Owned Switchgear

• 02/03/10 Sheet 1
  • Made into formal title page, content now starts on sheet 2.
  • Added WYE to title for clarification.
  • Added statement, specifying CRS 6-09-199 is part of the Rules for Electric Meter and Service Installation (REMSI) Website.
• 02/03/10 Sheet 2
  • Extended review period of unapproved switchgear and termination compartments from 60 to 90 days
  • Notes Section 1 – updated statement to include Point of Contact Document reference.
• 02/03/10 Sheet 3
  • Notes Section 10 – has been expanded to give more detail on conduit runs.
  • Notes Section 12 – hole in door of termination and metering compartments has been changed from ¼" to ½" to accommodate lockable hasp.
• 02/03/10 Sheet 4
  • Notes Section 15 – detail on PPL EU Phase rotation has been added for clarity.
  • Notes Section 18 – has been added.
  • Notes Section 19 – has been added.
  • Bill of Material Chart has been moved to Sheet 5.
• 02/03/10 Sheet 5
  • Termination Compartment Drawing has been moved to Sheet 6
  • Removed Reference to REMSI Sketch #37, Sketch has been Voided.
• 02/03/10 Sheet 6
  • Metering Compartment Drawing has been moved to Sheet 7.
  • Termination Compartment Drawing-Updated minimum working clear space in front of termination compartment to 9'0" from 5'0".
• 02/03/10 Sheet 7
  • Metering Compartment Drawing-Added references to Note 18 and Note 19.
  • Removed Detail B. Terminal Block is to be attached to Neutral Bar; previously Terminal Block was attached to the side of the Termination Compartment.
  • Updated minimum working clear space in front of metering compartment to 9'0" from 5'0".

Rule 1 - 7/29/11

• Edited Rule 1h
• Added Rule 1i
• Re-lettered rule accordingly

Rule 2 - 3/4/11

• Section B added, following sections re-lettered.
• Sections E and F (Formerly D and E) revised.
• Note 6 Revised.

Rule 6 - 10/26/11

• Section B title Updated
• Section C title Updated, added last two paragraphs detailing rear lot service requirements
  

Rule 11B - 10/26/11 Section E - added last paragraph detailing rear lot service requirements

Rule 12 - 7/29/11 Added Section j - Grounding

3/4/11 Section f revised.

Rule 13 - 10/26/11

• Section B - added exception meter height in flood area
• Section C - added exception indoor location in flood area

Rule 15 - 8/12/11 Updated to include Sketch #8D and Sketch 16 Series

3/4/11 Corrected terminology
            

          Rule 18 - 8/12/11  Updated to include Sketch #8D and Sketch 16 Series

Rule 19 - 10/26/11 Section G added, re-lettered Cut-In Card Documents to Section H

7/29/11

• Updated Section b
• Inserted Section c - Inspection Exemption - Ralroad Not Covered in NEC
• Re-lettered rule accordingly
• Updated Cut-In-Cards

Rule 25A - Updated wording in 25A(a)(1) to remove requirement of installation and annual maintenance fees on demand pulse contracts.